Repairing our Sonya SYW-70S Washing Machine

So!  We’ve been enjoying this machine for an amazing four years now!  I’m definitely at the point where if it blew up and I had to re-purchase, I’d consider it to have saved us in hassle and costs compared to hitting up the laundromat or something similar.

Last year though, when we left for Christmas, I made the error of not disconnecting the incoming water line from the machine.  I guess I felt that draining the house water lines would also drain water out of the solenoid valve of the machine, but perhaps that wasn’t to be.  When we returned and I attempted to do a load of laundry, lo and behold, no satisfying click, followed by the sound of water trickling into the washer.

I left it for a bit to see if it just was taking awhile to thaw out, but eventually gave up and decided that I had permanently damaged the solenoid.

My big brain came up with a great solution – just move the cold water connection to the hot water input, and then do hot water washes from now on (or at least, ask the machine to do hot water washes).  This worked just fine, but did have a few down sides.  The first was, previously, you could just pick your programme and press start.  But now you had to preselect hot water before your programme.  This also had trickle down effects all the way to the end of the cycle – even with a hot water wash selected, it defaulted to a cold water rinse.  So we had to remember wjen we washed a load to cancel the programme and re-run another cycle without detergent to do the rinse.  This also meant that the cycle ended prematurely, so AGAIN we had to finally run a programme of just spinning before we could hang the laundry.

Left is “cold” water input, right is “hot”.  We’ve been on “hot” for a year now.

This was all much easier than washing by hand or even the smaller loads but equal hassle of the Panda machine.  Still, it was a bit disappointing compared to what we had been use to.

We worked this way for all of 2019 – until we returned again from our Christmas vacation in Southern Ontario.  This time the machine was already pulled out from the wall, and I had correctly remembered to disconnect the hose and ensure everything was properly drained.  I noted the screws holding down the plate over the solenoids, so I removed them to just glance inside.  It looked like there were more screws holding both the hot and cold solenoids in place, and perhaps they were physically pressed into the bracket – not that fun of a job.  I delayed for a day when I knew I had a fair bit of time to cipher out a way to exchange the solenoids.

Still pulled out from Christmas Break
The next day I unplugged the machine (Safety first!  Or at least eventually…) and removed the cover again.  As I brandished the screwdriver towards the machine threateningly, I had a sudden realization.  The wires controlling the solenoids were attached with standard blade type connectors…
Rats, this looks like a finicky job.
Why would I swap solenoids, when I could just swap the wires and “trick” the machine into opening the hot solenoid using the cold wires, and perhaps vice versa…
Just swap wires!  Why didn’t I think of that a year ago??

I simply removed all the wires, and connected back up the hot water solenoid to the cold water wiring (I did have to cut the tie wrap holding the wires to get a couple of centimetres of slack).  Truth be told, I didn’t bother connecting the hot water wires to the cold water side – that solenoid still seems to be a lost cause, and we don’t have access to hot water anyway).

Looks like it was meant to be.
Whelp, it worked a charm.  Took maybe three minutes work in total.  Solved a problem we had just endured for a year.

I wish I was rich in money so I could just pay other people to fix problems as they occur.  Then again, better yet, I’m rich in that I have a loving, patient family willing to put up with minor annoyances with few complaints.

We have water!  Note the extreme iron staining.  Sigh.

2 thoughts on “Repairing our Sonya SYW-70S Washing Machine”

  1. do you know how to take out the bottom spinning disc inside the washer? i dont know what its called.. somehow i cant take it off cuz i think theres a lot of stuff inside there that my machine keeps stopping.. maybe its clogged.. if i do try to take it out maybe it might break

    • Hey Mike,
      Sorry, I don’t, I haven’t dismantled mine that far yet. Have you tried going down from inside the drum? There’s a little plastic cover in the centre bottom that looks like it could pop out and give you access to a removal bolt or something?


Leave a comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.